![AEStechnical](/img/default-banner.jpg)
- Видео 30
- Просмотров 114 181
AEStechnical
США
Добавлен 4 янв 2010
Видео
Enviro Pellet stove ash pan latch not tight?
Просмотров 347 месяцев назад
Ash pan and doors on a pellet stove need to have a tight seal. This video shows a loose latch, which will yield poor air flow through the burn pot and slow ignition. What the user will notice is "pellets are not being consumed at the rate they are feeding" (they will think the stove is feeding to much fuel) Or they will notice the stove is taking to long to ignite. The flame would be on the laz...
SIT 820 gas valve, adding the GTM remote control hardware
Просмотров 7989 месяцев назад
A quick overview of the SIT Proflame GTM kit for SIT 820 gas valve system. If you have the very common SIT 820 gas valve in your gas fireplace, and if you gas fireplace manufacture offers this "GTM" remote kit as an optional remote control system; This Proflame GTM remote will turn the burner on/off, as well as provide thermostat function and flame modulation. This GTM kit is powered from the 4...
Enviro S50 glass removal & re install
Просмотров 458Год назад
Rick of AES showing how to remove and re-install the curved glass on Enviro S50. Key point = DO NOT USE YOUR HE-MAN ELECTRIC BOLT DRIVER...your not putting lug nuts on a semi-truck... you only want gentle pressure when you tighten the bolts down
Duravent Direct Vent Coaxial/Concentric Flex Venting
Просмотров 712Год назад
Let's have a look at this product that most of us have not been paying attention to... but it has been available for a while now - the Duravent Direct Vent Coaxial/Concentric Flex Venting. And if your brand of fireplace has approved this product, it should be very useful in many installations.
Duravent 6DVL-ADC , single wall stovepipe adapter
Просмотров 2 тыс.3 года назад
how to make the transition from the support box to the single wall black stove pipe below the support box (or if your chimney is going through the wall, then we would use this piece from the thimble to the stovepipe) 810000900
Duravent 6DVL-AD stovetop adapter
Просмотров 10 тыс.3 года назад
810000915 6DVL-AD , use this piece to make a clean connection at the stove collar to your DVL (double wall) close clearance connector pipe
Duravent 6DVL-ADT 6" double wall chimney adapter
Просмотров 4,2 тыс.3 года назад
how to transition from the DVL double wall (close clearance connector) pipe coming up from the wood stove.... this part makes that connection to the support box
Duravent stovepipe adapter ADC
Просмотров 6203 года назад
If you have Duratech or DuraPlus Class A chimney system from the ceiling up... then this is used to make the transition from single wall to the support box.
SIT 820 Nova gas valve t-couple connection
Просмотров 34 тыс.3 года назад
For this very common gas valve we have 2 places to connect our thermocouple. And we need to pay extra attention to ensure we have a really good connection!!
Flame Tec IF-20 Smart Remote
Просмотров 3613 года назад
The Flame Tec IF-20 Smart Remote allows you to use your Android or Apple device to control your fireplace... it includes a thermostat function NOT found on Flame Bug (see the other video for that product).
Flame Tec Firebug
Просмотров 5574 года назад
Unboxing and using the "Firebug" bluetooth fireplace controller. It replaces any "switch" (wall switch? t-stat? standard remote?) so that you will use your phone or tablet with the app to turn your fireplace on and off.
Modern Flame Landscape Pro Multi down lights
Просмотров 2044 года назад
AES sales team Mario and Steve demonstrate the "down lights" (overhead lights) on the Modern Flame electric fireplace model "Landscape Pro Multi"
Modern Flame Landscape Pro Multi /Ember bed lights only
Просмотров 1354 года назад
Modern Flame Landscape Pro Multi /Ember bed lights only
Modern Flame Landscape Pro Multi / controlling the flame and down light
Просмотров 6114 года назад
Modern Flame Landscape Pro Multi / controlling the flame and down light
Modern Flame Landscape Pro Multi, electric fireplace, How to use the remote
Просмотров 3,4 тыс.4 года назад
Modern Flame Landscape Pro Multi, electric fireplace, How to use the remote
Kingsman/Marquis ZRB46 display in Kent WA
Просмотров 1,3 тыс.5 лет назад
Kingsman/Marquis ZRB46 display in Kent WA
SIT Proflame 2 gas fireplace remote 20190815 133117
Просмотров 10 тыс.5 лет назад
SIT Proflame 2 gas fireplace remote 20190815 133117
how to remove or install Enviro Kodiak woodstove secondary air tube
Просмотров 58510 лет назад
how to remove or install Enviro Kodiak woodstove secondary air tube
Dura Vent pellet vent pro, clean out tee cap / plug removal video
Просмотров 16 тыс.10 лет назад
Dura Vent pellet vent pro, clean out tee cap / plug removal video
Black Olive pellet grill routine cleaning
Просмотров 3,6 тыс.11 лет назад
Black Olive pellet grill routine cleaning
Chris Urban presents the BEEFEATER Aussie style gas grill / BBQ...perfect for searing
Просмотров 17 тыс.11 лет назад
Chris Urban presents the BEEFEATER Aussie style gas grill / BBQ...perfect for searing
Thanks, Nice, and how to restore the contact to spark generator, the light grey plastic on the top of the valve.
I have this same 820 SIT Valve. When I press in on PILOT, I get gas to the pilot, and to the main burner. Aside from that, it works normal. Of course this also means when you turn from ON to PILOT, it stays running. I don't care, because I'm happy to manually start and stop this only when I use it. I'm just unsure if there is a safety issue here? I'm starting to think this has a diaphragm in it that is ruptured, that could cause this?
Thank you so much for this video. I wanted to replace the ageing thermocouple on my FMI natural gas fireplace. The thermocouple was routed from the rear of the valve and made it very difficult to remove. After disassembling the thermocouple, I discovered a white plastic piece and a loose blue wire dangling from the rear of the valve. I had no idea where they came from or what their purpose was. I searched RUclips and came across your thorough presentation on the two possible thermocouple connections on the SIT 820 NOVA Gas Valve. You also answered what these two pieces were and how they contribute to the overall safety of the fireplace. In the end I opted for the t-connection in the front of the valve, making it a whole lot easier to access if I ever have to replace the t-connection again. Thanks again!
It needs separate ignitor?
You saved me $250!! Thank you !!!!!!
Best video ever
Does it need to be screwed to the flue collar??
Yesterday we visited some people at an airbnb. It had one of these fireplaces with the controller in this video except the fireplace was about half as wide. Nobody could get it to work so I decided to try. But I couldn't get it to respond either so I went to RUclips and learned there are buttons next to the power switch which did turn the fireplace on, but it was only cosmetic flames, the heat button didn't seem to do anything. The controller doesn't appear to have replaceable batteries. Is there a usb charge hole I didn't notice? What is going on here?
Very helpful video. Feel much more confident in my ability to service this unit. Ideally I will be supervising...thank you for this video.
Lol why was I recommended this, I don’t even own one? At least I watched it, so I know if I ever do get one I now know how to replace the S50 glass
❣️ promo sm
You save my life!! Thanksssa
Can you help me . When it goes in support box does it go on the outside lip or do I got to hammer that lip out some to fit inside it?
you spent way to much time on this video. What size is it. standard metric???
Do you need this to connect your DVL pipe to the stove collar? Thank You.
This video saved my day today . I had it into the rear of the valve . (Like the old valve ) the new one was set to the front option. Never knew . Great video !!! Thank you !
Do you have an adapter from rectangle to a circle
Yep, right here. I caught one. The "police" poored diet down it to. They left. A month late, The first responders said it was soot buildup. Or, a body... You'll never be able to tell if there's someone in the chimney. . I just saw the Kent fire on RUclips. I used to live there but I thought they took everything out. Or it's another body. Heidi's little sister. I think she tried to crawl in , and kill someone for drugs. . Or' they went for more diet soda, and didn't take the first body out. Who knows.
Hola, luego de ver tu video de una válvula parecida a la de mi caldera me surge hacerte una pregunta. Sabes si la válvula Elettrosit 810 s2 lleva también una pila, ya que enciende el piloto pero los quemadores no. Muchas gracias
What kind of battery?
Battery size CR20/25
@@AsiaSamiyah Thank you for the information on the battery. Would you happen to know how to sync the remote to the fireplace?
My outer skin doesn't come off!!!! The inner skin doesn't come out!!!! Help please
All pellet stove connector pipes are trash, can’t stand the junk they use. Why can’t it connect like wood stove double wall pipe, crimped and screws.
The thermostat connection on mine randomly stops and I have to jiggle it for it to turn on. Not the wire the connection on the nova gas valve. Is there a way to fix that? I put a little force on it and it turns the gas stove on and stays on but it seems like it doesn’t connect for long and shuts off.
it is considered common maintenance to remove t-stat wire and clean the ends of the wire (both at the valve and at the t-stat) and reattach to ensure a solid connection. if the issue is internal to the gas valve it must be replaced
Hey there. Thank you for this video and for responding to comments. I just installed a brand new valve (replaced a Honeywell), but in the testing phase, whenever I turned from OFF to PILOT, it opened the valve to the pilot- allowing gas to flow even without manually depressing the pilot button. I've replaced a couple of these before and this has never happened. Thought maybe it was to do with having assumed I would run the thermocouple off the front valve outlet, and maybe it needs to run off the rear? Or maybe just a bad magnet? How is the thermo position determined? Or can one simply choose which port to use for the thermo, so long as the blue wire is also connected there? Thanks!
The valve should not do that. So either a bad valve or something is hooked up wrong, and I'm not sure what could be hooked up wrong to make the gas flow before it is supposed to... not good
Thanks for this video. I have several of these valves and the low setting is now low enough. Is there a way to adjust the High/Low adjustment so the flow can be reduced more? Or do I have to add an external regulator and then increase the pilot flow?
Your appliance is only tested and listed between a certain range from high to low...so I would not mess with that. Nor would I add another regulator upstream...then everything would be off. Delayed ignition can be a serious problem if your manifold pressure is to low.
@@AEStechnical Thank you. Is there a compatible SIT model (or other) that would have a larger adjustable range?
@@stevenchristini2263 SIT has different regulators for the valve. (The part with the High/Low knob). BUT...your appliance is designed for the range they made it with, tested it with. Changing that could lead to problems like delayed ignition or combustion problems.
@@AEStechnical OK. Thank you very much for all of this information. Very helpful!
Hi thanks for this video. Question on this exact valve. It’s started with pilot not staying on, after turning to on position. Have replaced thermocouple. No luck still pilot won’t stay on. And now for some reason, not getting any gas to pilot at all. Have taken the valve apart, clean it, still no gas at pilot. Your advice will be appreciated.
1st- I would NEVER EVER recommend taking the gas valve apart. There are no field serviceable parts inside. 2nd--if your thermocouple is generating enough voltage and the connection from the thermocouple to the gas valve is solid and correct to conduct the 10 to 20 millivolts and it still does not hold pilot... then it is either a bad gas valve or you have other parts in this electrical loop (like a vent spill switch)
Hello, I watched your video on the SIT 820 Nova gas valve t-couple connection. My t-couple will not thread into either port. It is the t- couple that was in the Honeywell 8420 bad valve. It really looks like it should thread into the Nova but it won't. Do I need a special Nova t-couple? Thanks for any help.
odd to get this comment on the vent adapter video? :) but I have not worked with a Honeywell gas valve in so many years I would hate to say for sure. But I do know that there are different threaded fittings for different types... So if I had to make a guess I would get a SIT thermo-couple.
Do you know what is wrong if I can’t use the Thermostat mode now. It was working fine and now it is not working so the fireplace now constantly stays on it won’t shut down when it’s reached the temp?
So many thanks ! You save my life !
Thank you! Very helpful!
will this fit on a jotul f400 wood stove? seems loose to me
I am not an expert on Jotul, but is possible they use a slightly different size flue outlet as they are European company. The adapter likely drops down further than other brand? But I suspect is still the correct part. Your Jotul dealer likely knows this one? Sorry I can't say for sure.
What did you end up doing? I have a Jotul and just purchased this as well. its loose. Any recommendations? Thanks!
@@muirg01same with my drolet stove . Not sure what to do.
I ended up getting rid of the adapter all together. The double wall telescoping end fit more snug into the stove top. Had to put some cement in the screw holes since the inner lining just barely passed them but it works. Been running solid
Do you know what holds the blue wire to the plastic valve in order to make contact with the thermocouple? I lost the internal connection for the plastic valve and it doesn't make the connection anymore with the thermocouple.
At the end of the blue wire is a flat metal plate (male spade connector). I believe it is both crimped onto the end of the wire and likely soldered too. This flat connector is slide into a special white plastic housing to hold it in place for the end of the thermocouple to be pressed firmly in place then it is tightened down (finger tight us 1/4 turn)
How do you turn it on with out Remote ? Sofi stadium with no remotes
The answer will depend on the exact model. You can contact Greg Burke, the national sales manager for Modern Flame, as he is very familiar with that specific project... I know that he would be happy provide the answer for you. I would call or text him @ 858-603-4643 You can let him know you were directed to him by Don @ AES. cheers!
There is a manual touch control in the upper right hand corner of the fireplace.
@@AsiaSamiyah thank you Anthony.
@@AEStechnical thank you so much for the info!
Can you help me figure out where to install the igniter wire?
The igniter will not normally attach to the gas valve. It will depend on the brand and model of the fireplace/stove.
I got one from Amazon in Australia, I absolutely love it, it’s winter here atm and this thing is lit, pellets are bit dear here that’s the only draw back I felt , but love the smokeless tech
what is the name of the white plastic that goes on the blue wire? I dropped mine where I can't retrieve it. And do you know where I can buy this part?
I am 99% sure that little plastic piece is NOT a part sold by itself. But if you know some fireplace gas techs (local gas fireplace shop) they might have some old valves they could cannibalize for that part?
Can this run without the heat?
yes
@@AEStechnical Hi, how do you turn the heat part off (not low or high) just off? Thank you.. just got one installed.
@@michaelheppler991 The heater can be turned on using the remote control or manual touch control in the upper right hand corner of the fireplace. The middle button on your manual touch control is for you're heater. Hit the button twice and it will initiate the low heater setting.
I have the Napoleon gx 70 an I changed batteries in both units syncing them up but I can’t adjust temp.
push the thermostat icon when you install the last battery. sounds like you disable the thermostat feature.
Thanks , hay- is there any way to test this valve with an ohm meter?
yes, we can test the resistance for the part of the valve that opens the main burner gas flow with a standard ohm meter. But to test the part of the valve that controls the pilot gas flow requires an expensive (rare) ohm meter to read super small amount of resistance.
what is the difference between a "Vent Free" valve and a non vent free valve. Can a valve for a fireplace like the one here with just a thermocouple be used instead of of using a valve with a thermocouple and a pilot generator ? Thank you
the valve is not the key whether it will work for a "vent free" or not... the pilot assembly in a vent free is very specific design called "ODS" which reacts to the percentage of oxygen in the room... Any combustion is burning up oxygen so the ODS design is a very accurate and safe way to ensure the burner will shut off before we have a problem.
Does the Firebug need to be more protected from the heat. A heat shield or anything else to keep it from getting too hot, or melt?
It will depend on the type of fireplace. Some of the newer models have very low clearance underneath and I would worry about over heating it. Most of the older models have much more room underneath and do not have nearly as much heat in that area. Plastics and circuit boards generally do not want to get hotter than about 140 degrees... so I would use an oven thermometer and test the place you intend to locate the receiver.
So helpful! thanks
Hi, where's the adjustment screw to adjust manifold gas pressure? Thanks
to adjust the manifold pressure would require changing the regulator.... unless it has the clever SIT regulator that has a special designed screw in the "High/Low" adjustment knob that can be flipped 180 degrees to change from NG to LP
Thanks so much, you saved me!!!!
you saved my relationship. someday I will find you, and buy you beers
I have got a gas valve the exact same one that the pilot light will stay lit and run all day long soon as I turn the gas on it fires up it will run for about 2 minutes a click and everything turns off what would that be
Did you ever find an answer to this? Having the same issue and I cannot work it out
2 things some to mind for this: 1) the thermocouple is not tightened into pilot assembly bracket (finger tight plus 1/4 turn). This results in the entire thermocouple getting hot instead of only the top 1/3 getting hot from the pilot flame. 2) once we start to get a good draft we are causing turbulence at the pilot flame. Could need a pilot shield or a method to slow down the draft.
Don, would that adapt go up into the support box but on the OUT side of the internal pipe between the box opening and the stainless pipe? NOT slip inside the inner pipe
you do NOT want the collar to go up on the inside of the inner pipe of the class A.... we want to preserve the "drip free" aspect of the system.... if we picture hot gooey creosote dripping down the inside of the chimney we want that mess to stay "inside" as it passes each joint... if we have a joint in the system where the inner pipe is wrong, then the mess can leak at that joint or "drip". I hope that answers your question.
@@AEStechnical that was my point. Just wanted to clarify for the non experts
ruclips.net/video/tV-TN_1Cch0/видео.html
Looks simple to install and easy to use. Thank you for making this video it is very helpful.
OMG, you are awesome. I was afraid I was going to have to buy a new remote!!!!